iFlight Chimera7 Pro HD BLITZ F722 F7 6S 7.5 inch Long Range FPV Racing Drone BNF w/ E55A ESC XING2 2809 1250KV Motor DJI FPV Air Unit
$620~690 – Check latest price on: AliExpress, Banggood
| iFlight Chimera7 Pro Specifications | |
|---|---|
| Brand | iFlight |
| Model | Chimera7 Pro |
| Weight | 695g (without battery and GoPro mount) |
| Total Dimensions | 258*200mm (body dimension) |
| Upper(middle) Plate Thickness | 3mm |
| Bottom to Top Distance | 20-29mm |
| ESC | BLITZ E55 4-IN-1 2-6S ESC |
| Camera Plate Thickness | 3mm |
| Bottom Plate Thickness | 3mm |
| Top Plate Thickness | 3mm |
| Geometry | DC (DeadCat) |
| Propellers | HQ 7.5X3.7X3 |
| Arm Thickness | 6mm |
| FC | BLITZ F722 |
| Motor | XING2 2809 1250KV |
| BLITZ F722 Flight Controller | Mount pattern: 30.5*30.5mm / 4mm PCB hole diameter Smartaudio / IRC Tramp VTX protocol supported Firmware target: IFLIGHT_BLITZ_F722 Motor outputs: 4x (SH1.0 connector) Flash: 32MB (Blackbox flash) I2C serial: SDA / SLA pads Dimensions: 36.5*35 mm Barometer: DPS310 OSD Chip: AT7456E LED controller: Yes MCU: STM32 F722 Beeper pad: Yes Gyro: BMI270 Weight: 7.8g UARTS: 6 |
| BLITZ E55 4-IN-1 2-6S 55A ESC | Supports: DShot DShot150/300/600/MultiShot/ OneShot etc. Mounting Holes: 30.5*30.5mm/Φ4mm Target: IFLIGHT_BLITZ_G2 Supports 2-6S Lipo input Current sensor: Yes Constant: 55 Amps Current rate: 200 Burst: 65 Amps Weight: 15.3g MCU： G071 BEC: No |
| XING2 2809 1250KV Motor | Model: XING2 2809 KV: 1250 Quantity: 1 PC Prop shaft: CW thread Recommended input voltage Voltage: 4S-6S (16V-26V) Configuration: 12N14P Stator Diameter: 35.33mm Weight: 60.7g with short wire Wire length: 18AWG 260mm Mounting pattern: 19*19mm |
Main Changelog from Chimera7 to Chimera7 Pro:
- New Lightweight Side Panels Design – Keep Your Rig Clean
- SucceX-D F7 V2.2 Stack (F7+50A ESC) upgraded to BLITZ F722 Stack (F7 V1.1 + 55A 4in1 ESC)
- XING 2806.5 upgraded to XING2 2809 1250KV
- 7-inch frame upgraded to 7.5inch
Highlights:
- 360° TPU protection, DJI cam protection and antenna mounts
- Battery voltage LED status light (illuminated IF logo on the bottom)
- GoPro TPU bottom stand (GoPro protector not included)
- No props in view (DJI Air unit record in 1080p/60fps)
- Lightweight Side Panels Design – Keep Your Rig Clean
- GPS pre-installed for more safety at a distance
- XING2 2809 1250KV efficient wide stator motors
- 6mm rigid arm design for more stiffness
- Top- and bottom battery mount option
PRE-TUNED & PRE-SETUP:
- Is this your first BNF or are you just starting through with FPV? This article might probably help: General Guide // iFlight BNF
- Don’t worry about tuning, we did that for you already! A basic PID- and Filter tuning was applied for a great flight experience!
To restore lost tunes or updates, please check our linked article on “Firmware/Factory Dumps” - Angle-Mode (self-balancing level mode) is enabled by default to make sure your first flight doesn’t end in a mess!
Please check our linked article on “How to disable Angle-Mode, activate Acro-Mode” - GPS Rescue is OFF by default to prevent unwanted or unexpected drone behavior.
Please check our linked article on”GPS Rescue Mode // Setup”
Check the iFlight Chimera7 Pro price:
- Check price on AliExpress
- Check price on Banggood
